Maus IgG1 isotype control (FITC)
-
- Target Alle IgG1 Produkte
- IgG1
-
Wirt
- Maus
- Konjugat
- FITC
- Applikation
- Flow Cytometry (FACS), Isotype Control (IsoC), Immunofluorescence (IF)
- Produktmerkmale
- This mouse monoclonal IgG1 was produced against a synthetic hapten, which is normally not present in humans or animals. Therefore, this mouse IgG1 does not react with any antigen of human or animal cells.
-
Klon
- ICIGG1
- Isotyp
- IgG1
-
Mouse IgG1 isotype control (Biotin)
FACS, ELISA, WB, IP, ICC, IHC (fro), IHC (p) Monoclonal MOPC-21 IgG1 kappa Biotin
Mouse IgG1 isotype control (FITC)FACS, ELISA Monoclonal 15H6 IgG1 FITC
Mouse IgG1 isotype control (PE)FACS, ELISA Monoclonal 15H6 IgG1 PE
Mouse IgG1 isotype controlFACS, ELISA, WB, IP, ICC, IHC (fro), IHC (p), Func Monoclonal MOPC-21 IgG1 kappa unconjugated
Mouse IgG1 isotype controlFACS, ELISA, WB, IP, ICC, IHC (fro), IHC (p) Monoclonal MOPC-21 IgG1 kappa unconjugated
Mouse IgG1 isotype control (SPRD)FACS, ELISA Monoclonal 15H6 IgG1 SPRD
Mouse IgG1 isotype control (APC)FACS, ELISA Monoclonal 15H6 IgG1 APC
Mouse IgG1 isotype control (Biotin)FACS, ELISA Monoclonal 15H6 IgG1 Biotin
Mouse IgG1 isotype control (PE-Cy7)FACS, ELISA Monoclonal 15H6 IgG1 PE-Cy7
Mouse IgG1 isotype control (APC-Cy7)FACS, ELISA Monoclonal 15H6 IgG1 APC-Cy7
-
- Applikationshinweise
- It is recommended for use in flow cytometry. This reagent is effective for direct immunofluorescence staining of human tissue for flow cytometric analysis using 20 µL/10^6 cells.
- Kommentare
-
Fluorescein isothiocyanate (Molecular Probes).
Excitation/Emission wavelength: 494 nm/514 nm - Aufbereitung der Proben
-
- Transfer 100 µL of anticoagulated (EDTA) blood to a 12 x 75 mm polystyrene test tube (10^6 cells). 2. Add 20 µL of Isotype Control IgG1 and mix gently with a vortex mixer. The 20 µL is a guideline only, the correct volume depends on the quantity of direct monoclonal used. 3. Incubate in the dark at room temperature at 4 °C for 30 minutes or at room temperature (20-25 °C) for 15 minutes. 4. Add 1,5 mL of Lysing Solution to each sample and mix gently with a vortex mixer. Incubate for 10 minutes at room temperature in the dark. 5. Centrifuge at 1000 x g for 5 minutes. Gently aspirate the supernatant and discard it leaving approximately 50 µL of fluid. 6. Add 2 mL 0.01 mol/l PBS (It betters that it containing 2 % bovine serum albumin) and resuspend the cells by using a vortex mixer. 7. Centrifuge at 1000 x g for 5 minutes. Gently aspirate the supernatant and discard it leaving approximately 50 µL of fluid. 8. Resuspend pellet in an appropriate fluid for flow cytometry, e.g. 0.3 mL PBS. The PBS should contain 1 % paraformaldehyde (fixative) if samples are not analysed the same day. 9. Analyse on a flow cytometer or store at 2-8 °C in the dark until analysis. Samples can be run up to 24 hours after lysis.
- Beschränkungen
- Nur für Forschungszwecke einsetzbar
-
- Konservierungsmittel
- Sodium azide
- Vorsichtsmaßnahmen
- 1. The device is not intended for clinical use including diagnosis, prognosis, and monitoring of a disease state, and it must not be used in conjunction with patient records or treatment. 2. This product contains Sodium azide (NaN3), a chemical highly toxic in pure form. At product concentrations, though not classified as hazardous, Sodium azide may react with lead and copper plumbing to form highly explosive build-ups of metal azides. Upon disposal, flush with large volumes of water to prevent metal azide build-up in plumbing. 3. As with any product derived from biological sources, proper handling procedures should be used.
- Handhabung
- Product is photosensitive and should be protected from light.
- Lagerung
- 4 °C
-
- Target
- IgG1
- Abstract
- IgG1 Produkte
- Synonyme
- IgG1 Isotype Control, Igh-4 Isotype Control, VH7183 Isotype Control, immunoglobulin heavy constant gamma 1 (G1m marker) Isotype Control, Ighg1 Isotype Control
- Substanzklasse
- Antibody
-
