rT3 ELISA Kit

Produktnummer ABIN8056329

Dieses Colorimetric ELISA kit dient der quantitativen Messung von Diverse Spezies rT3.

Kurzübersicht für rT3 ELISA Kit (ABIN8056329)

Target: rT3 (Reverse Triiodothyronine T3 (rT3))

Reaktivität: Diverse Spezies

Nachweismethode: Colorimetric

Methodentyp: Competition ELISA

Detektionsbereich: 24.69 pg/mL - 2000 pg/mL

Applikation: ELISA

Proben: Plasma, Serum

Güteklasse: High Sensitivity

Produktdetails rT3 ELISA Kit

Untere Nachweisgrenze: 24.69 pg/mL

Verwendungszweck: The kit is a high sensitivity competitive inhibition enzyme immunoassay technique for the in vitro quantitative measurement of rT3 in serum, plasma.

Analytische Methode: Quantitative

Spezifität:

This assay has high sensitivity and excellent specificity for detection of High Sensitive Reverse Triiodothyronine (rT3).
No significant cross-reactivity or interference between High Sensitive Reverse Triiodothyronine (rT3) and analogues was observed.

Sensitivität: < 9.04 pg/mL

Bestandteile:

• Pre-coated, 96-well strip plate
• Plate sealer
• Standard
• Standard Diluent
• Detection Reagent A
• Assay Diluent A
• Detection Reagent B
• Assay Diluent B
• Reagent Diluent
• Stop Solution
• TMB Substrate
• Wash Buffer (30X)
• Instruction manual

Benötigtes Material:

• Microplate reader with 450 ± 10nm filter.
• Precision single or multi-channel pipettes and disposable tips.
• Eppendorf Tubes for diluting samples.
• Deionized or distilled water.
• Absorbent paper for blotting the microtiter plate.
• Container for Wash Solution

Anwendungsinformationen

Probenmenge: 50 μL

Testdauer: 3 h

Plattentyp: Pre-coated

Protokoll: 1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
    And then add 50µL prepared Detection Reagent A immediately.
    Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
7. Add 50µL Stop Solution. Read at 450 nm immediately.

Aufbereitung der Reagenzien:

1. Bring all kit components and samples to room temperature (18-25°C) before use. If the kit will not be used up in one time, please only take out strips and reagents for present experiment, and leave the remaining strips and reagents in required condition.
2. Standard - Reconstitute the Standard with 0.5 mL of Standard Diluent, kept for 10 minutes at room temperature, shake gently(not to foam). The concentration of the standard in the stock solution is 2,000pg/mL. Please prepare 5 tubes containing 0.6 mL Standard Diluent and produce a triple dilution series according to the picture shown below. Mix each tube thoroughly before the next transfer. Set up 5 points of diluted standard such as 2,000pg/mL, 666.67pg/mL, 222.22pg/mL, 74.07pg/mL, 24.69pg/mL, and the last EP tubes with Standard Diluent is the blank as 0pg/mL.
3. Detection Reagent A and Detection Reagent B - Briefly spin or centrifuge the stock Detection A and Detection B before use. Dilute them to the working concentration 100-fold with Assay Diluent A and B, respectively.
4. Wash Solution - Dilute 20 mL of Wash Solution concentrate (30x) with 580 mL of deionized or distilled water to prepare 600 mL of Wash Solution (1x).
5. TMB substrate - Aspirate the needed dosage of the solution with sterilized tips and do not dump the residual solution into the vial again.

Note:

1. Making serial dilution in the wells directly is not permitted.
2. Prepare standard within 15 minutes before assay. Please do not dissolve the reagents at 37°C directly.
3. Detection Reagent A and B are sticky solutions, therefore, slowly pipette them to reduce the volume errors.
4. Please carefully reconstitute Standards or working Detection Reagent A and B according to the instruction, and avoid foaming and mix gently until the crystals are completely dissolved. To minimize imprecision caused by pipetting, use small volumes and ensure that pipettors are calibrated. It is recommended to suck more than 10μL for one pipetting.
5. The reconstituted Standards, Detection Reagent A and Detection Reagent B can be used only once.
6. If crystals have formed in the Wash Solution concentrate (30x), warm to room temperature and mix gently until the crystals are completely dissolved.
7. Contaminated water or container for reagent preparation will influence the detection result.

Beschränkungen: Nur für Forschungszwecke einsetzbar

Handhabung

Handhabung:

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Lagerung: 4 °C,-20 °C

Informationen zur Lagerung:

• For unopened kit: All the reagents should be kept according to the labels on vials. The Standard, Detection Reagent A, Detection Reagent B and the 96-well strip plate should be stored at -20°C upon receipt while the others should be at 4°C.
• For opened kit: When the kit is opened, the remaining reagents still need to be stored according to the above storage condition. Besides, please return the unused wells to the foil pouch containing the desiccant pack, and reseal along entire edge of zip-seal.
  Note: It is highly recommended to use the remaining reagents within 1 month provided this is within the expiration date of the kit.
• For ELISA kit, 1 day storage at 37°C can be considered as 2 months at 4°C, which means 3 days at 37°C equaling 6 months at 4°C.

Haltbarkeit: 6 months

Details zu rT3

Target: rT3 (Reverse Triiodothyronine T3 (rT3))

Andere Bezeichnung: Reverse Triiodothyronine

Hintergrund: RT3, r-T3, Reverse T3,(2S)-2-Amino-3-[4-(4-Hydroxy-3,5-Diiodophenoxy)-3-Iodophenyl]propanoic Acid, 3,3',5'-Triiodo-L-thyronine