Endothelin 1 ELISA Kit

Produktnummer ABIN578988

Produktdetails Endothelin 1 ELISA Kit

Target: Endothelin 1 (EDN1)

Reaktivität: Ratte

Nachweismethode: Colorimetric

Methodentyp: Sandwich ELISA

Detektionsbereich: 4.69-300 pg/mL

Untere Nachweisgrenze: 4.69 pg/mL

Applikation: ELISA

Verwendungszweck: This immunoassay kit allows for the in vitro quantitative determination of rat ET-1 concentrations in serum, plasma and other biological fluids.

Proben: Plasma, Serum

Analytische Methode: Quantitative

Spezifität: This assay recognizes recombinant and natural rat ET-1.

Kreuzreaktivität (Details): No significant cross-reactivity or interference was observed.

Sensitivität: The sensitivity of this assay, or Lower Limit of Detection (LLD) was defined as the lowest detectable concentration that could be differentiated from zero.

Produktmerkmale: Rattus norvegicus,Rat,Endothelin-1,ET-1,Preproendothelin-1,PPET1,Edn1

Bestandteile: Reagent (Quantity ): Assay plate (1), Standard (2), Sample Diluent (1 × 20ml), Assay Diluent A (1x10ml), Assay Diluent B (1x10ml), Detection Reagent A (1 × 120μl), Detection Reagent B (1 × 120μl), Wash Buffer (25 x concentrate) (1 × 30ml), Substrate (1x10ml), Stop Solution (1x10ml), Plate sealer for 96 wells (5), Instruction (1)

Benötigtes Material: Microplate reader. Pipettes and pipette tips. EP tube Deionized or distilled water.

Anwendungsinformationen

Probenmenge: 100 μL

Plattentyp: Pre-coated

Protokoll: The microtiter plate provided in this kit has been pre-coated with an antibody specific to ET-1. Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated polyclonal antibody preparation specific for ET-1. Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then a TMB substrate solution is added to each well. Only those wells that contain ET-1, biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm 2 nm. The concentration of ET-1 in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Aufbereitung der Reagenzien:

Bring all reagents to room temperature before use. Wash Buffer - If crystals have formed in the concentrate, warm to room temperature and mix gently until the crystals have completely dissolved. Dilute 20 mL of Wash Buffer Concentrate into deionized or distilled water to prepare 500 mL of Wash Buffer. Standard - Reconstitute the Standard with 1.0 mL of Sample Diluent. This reconstitution produces a stock solution of 1000 pg/mL. Allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making serial dilutions. The undiluted standard serves as the high standard (1000 pg/mL). The Sample Diluent serves as the zero standard (0 pg/mL). Detection Reagent A and B - Dilute to the working concentration specified on the vial label using Assay Diluent A and B (1:100), respectively.

Probennahme: Plasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 15 minutes at 1000 x g at 2 - 8 °C within 30 minutes of collection. Store samples at ≤ -20 °C. Avoid repeated freeze-thaw cycles. Note: Citrate plasma has not been validated for use in this assay.

Testdurchführung:

Allow all reagents to reach room temperature. Arrange and label required number of strips.
1. Prepare all reagents, working standards and samples as directed in the previous sections.
2. Add 100 uL of Standard, Control, or sample* per well. Cover with the adhesive strip. Incubate for 2 hours at 37 °C.
3. Remove the liquid of each well, don’t wash.
4. Add 100 uL of Detection Reagent A to each well. Incubate for 1 hour at 37°C. Detection Reagent A may appear cloudy. Warm to room temperature and mix gently until solution appears uniform.
5. Aspirate each well and wash, repeating the process three times for a total of three washes. Wash by filling each well with Wash Buffer (350 uL) using a squirt bottle, multi-channel pipette, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against clean paper towels.
6. Add 100 uL of Detection Reagent B to each well. Cover with a new adhesive strip.Incubate for 1 hours at 37 °C.
7. Repeat the aspiration/wash as in step
5. 8. Add 90 uL of Substrate Solution to each well. Incubate for 30 minutes at room temperature. Protect from light.
9. Add 50 uL of Stop Solution to each well. If color change does not appear uniform, gently tap the plate to ensure thorough mixing.
10. Determine the optical density of each well within 30 minutes, using a microplate reader set to 450 nm.
Important Note:1. The wash procedure is critical. Insufficient washing will result in poor precision and falsely elevated absorbance readings.
2. It is recommended that no more than 32 wells be used for each assay run if manual pipetting is used since pipetting of all standards, specimens and controls should be completed within 5 minutes. A full plate of 96 wells may be used if automated pipetting is available.
3. Duplication of all standards and specimens, although not required, is recommended.
4. When mixing or reconstituting protein solutions, always avoid foaming.
5. To avoid cross-contamination, change pipette tips between additions of each standard level, between sample additions, and between reagent additions. Also, use separate reservoirs for each reagent.
6. To ensure accurate results, proper adhesion of plate sealers during incubation steps is necessary.

Ergebnisberechnung:

Average the duplicate readings for each standard, control, and sample and subtract the average zero standard optical density. Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the y-axis against the concentration on the x-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the ET-1 concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. This procedure will produce an adequate but less precise fit of the data. If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.

Beschränkungen: Nur für Forschungszwecke einsetzbar

Handhabung

Handhabung: 1. The kit should not be used beyond the expiration date on the kit label.
2. Do not mix or substitute reagents with those from other lots or sources.
3. If samples generate values higher than the highest standard, further dilute the samples with the Assay Diluent and repeat the assay. Any variation in standard diluent, operator, pipetting technique, washing technique,incubation time or temperature, and kit age can cause variation in binding.
4. This assay is designed to eliminate interference by soluble receptors, ligands, binding proteins, and other factors present in biological samples. Until all factors have been tested in the Immunoassay, the possibility of interference cannot be excluded.

Lagerung: 4 °C/-20 °C

Informationen zur Lagerung: The Standard, Detection Reagent A, Detection Reagent B and the 96-well strip plate should be stored at -20 °C upon being received. The other reagents can be stored at 4 °C.

Details zu Endothelin 1

Target: Endothelin 1 (EDN1)

Andere Bezeichnung: Edn1 (EDN1 Produkte)

Synonyme: et1 ELISA Kit, et-1 ELISA Kit, Edn1 ELISA Kit, EDN ELISA Kit, ET-1 ELISA Kit, ET1 ELISA Kit, PPET1 ELISA Kit, HDLCQ7 ELISA Kit, preproET ELISA Kit, Et1 ELISA Kit, fb14d01 ELISA Kit, wu:fb14d01 ELISA Kit, PPET-1 ELISA Kit, EDN1 ELISA Kit, edn1 ELISA Kit, edn1-a ELISA Kit, edn1-b ELISA Kit, endothelin 1 ELISA Kit, endothelin 1 S homeolog ELISA Kit, endothelin 1 L homeolog ELISA Kit, edn1 ELISA Kit, EDN1 ELISA Kit, Edn1 ELISA Kit, edn1.S ELISA Kit, edn1.L ELISA Kit

Hintergrund: Endothelin-1 (ET-1), a peptide of 21 amino acid residues, is the most potent vasoconstrictive substance known. Originally isolated from porcine aortic endothelial cells, ET-1 is now known to be one of a family of three mammalian vasoactive peptides that also includes Endothelin-2 (ET-2) and Endothelin-3 (ET-3). These related peptides differ from ET-1 at two and six amino acid residue positions, respectively. A fourth peptide, vasoactive intestinal contractor (VIC), is sometimes classified as rat ET-2. All members of the endothelin family contain two essential disulfide bridges and six conserved amino acid residues at the C-terminus. Additionally, all of the endothelin family members are synthesized initially as prepropolypeptides of approximately 200 amino acid residues encoded by separate genes. These are proteolytically cleaved to produce biologically-inactive propolypeptides of approximately 40 amino acid residues termed “ big endothelins ” . Big ET-1 is cleaved by the proteolytic action of a membrane-bound metalloprotease [endothelin-converting enzyme (ECE-1)] producing the 21 amino acid residue active peptide. The biochemistry and biology of the endothelins have been the subject of several reviews.

Gen-ID: 3168

Pathways: Hormone Transport, Negative Regulation of Hormone Secretion, Regulation of Systemic Arterial Blood Pressure by Hormones, cAMP Metabolic Process, Regulation of Muscle Cell Differentiation, Regulation of G-Protein Coupled Receptor Protein Signaling, Regulation of Cell Size